Patton electronic 2168 Instrukcja Użytkownika

USER MANUAL CopperLink™ Ethernet ExtendersModel 2158 & 2168 SALES OFFICE(301) 975-1000TECHNICAL SUPPORT(301) 975-1007 Part# 07M2158_2168 Rev. AD

10 6. Connect the Ethernet interface (refer to section 3.4, “Connecting the 10/100Base-T Ethernet Interface” on page 11). 3.3 CONNECTING THE TWIS

11 The terminal block connector on the CopperLink Ethernet Extender's twisted pair interface is polarity insensitive and is wired for a two-

12 Connecting the 10/100Base-T Ethernet Port to a Hub The CopperLink Ethernet Extender 10/100Base-T interface is configured as DTE (Data Terminal Equi

13 DC power (supplied via the power supply jack to the CopperLink Ether-net Extender) must meet the following requirements; DC power supplied must be

14 4.0 CONFIGURATION (MODEL 2168 ONLY) The CopperLink Ethernet Extender has eight DIP switches for configur-ing the unit for a wide variety of applic

15 Figure 10. Model 2168 standalone modem DIP switch orientation Figure 11. Model 2168 rack card DIP switch orientation

16 4.2 CONFIGURING DIP SWITCH S1 DIP switch S1 is where you configure the CopperLink line rate, symmet-ric or asymmetric, Ethernet full auto negotiat

17 Table 3: Asymmetric CopperLink Line Rates Selection Chart S1-2 S1-3 S1-4 Asymmetric Line Rates DS/US OFF OFF ON 4.17 Mbps/1.56 Mbps (Mode 0)OFF O

18 5.0 OPERATION Once the CopperLink Ethernet Extenders are properly installed, they should operate transparently. No user settings required. This s

19 Table 5: Front panel LED description for standalone modem LED Description Power On (green) when power is applied to the unit. Off when no powe

2 CONTENTS1.0 Warranty Information ... 4 1.1 Radio and TV Interference...

20Figure 13. CopperLink Ethernet Extender rack card front panelTable 6: Front panel LED description for rack card modemLED DescriptionPower Solid GREE

21APPENDIX ASPECIFICATIONSA.1 LAN CONNECTION• Shielded RJ-45, 10/100Base-T, IEEE 802.3 Ethernet• CopperLink Connection: RJ-45 and Terminal BlockA.2

22A.8 TEMPERATURE RANGE32–122°F (0–50°C)A.9 HUMIDITYUp to 90% non-condensing.A.10 DIMENSIONS1.58H x 4.16W x 3.75D in. (10.6H x 4.1W x 8.8D cm)

23APPENDIX BMODEL 2158 SERIES FACTORY REPLACEMENT PARTS AND ACCESSORIES*Only required with optional UI power supply (08055DCUI)Patton Model # Descript

24APPENDIX CMODEL 2168 SERIES FACTORY REPLACEMENT PARTS AND ACCESSORIES*Only required with optional UI power supply (08055DCUI)Patton Model # Descript

25APPENDIX DCOPPERLINK SERIES INTERFACE PIN ASSIGNMENTD.1 10/100BASE-T INTERFACERJ-45• Pin 1: TX+• Pin 2: TX-• Pin 3: RX+• Pin 6: RX-• Pins 4, 5, 7,

26APPENDIX EDISTANCE CHART, BASED ON 24 AWG (0.5 MM)Note Model 2158 is fixed at 12.5 Mbps, 4,000 ft (1,220 m).Symm Line Rate (DS/US) Distance in feet (

27Notes_______________________________________________________________________________________________________________________________________________

28Notes_______________________________________________________________________________________________________________________________________________

3 D CopperLink Series Interface Pin Assignment... 25 D.1 10/100Base-T Interface ...

4 1.0 WARRANTY INFORMATION Patton Electronics warrants all CopperLink Ethernet Extender compo-nents to be free from defects, and will—at our option

5 1.3 SERVICE All warranty and non-warranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a Retu

6 2.0 GENERAL INFORMATION Thank you for your purchase of this Patton Electronics product. This product has been thoroughly inspected and tested and

7 passing packets across the CopperLink link that are meant for the remote peered LAN. Figure 1. Typical application The CopperLink/L modem and Copp

8 3.0 INSTALLATION Because the CopperLink Ethernet Extender requires no configuration, it can be installed quickly. If you are installing a standalon

9 3.2 RACK CARD INSTALLATION The CopperLink Ethernet Extender rack card comprised a front card and a rear card.Do the following to install the cards